Recharge before its power is completely consumed. Status of LED display shows different levels of the Power Bank capacity available: Reminder: Disconnect the Power Bank from the AC power adapter after it’s fully charged. When the Power Bank is fully charged, all the 4 LED lights will glow steady. Reminder: The Power Bank will become warm during the charging. To charge the EL1697, simply plug the DC-out jack of the AC adapter (included in the package) into the “INPUT” socket of the Power Bank and connect the AC power plug of the adaptor to a AC wall-outlet.ĭuring charging, all the 4-stage blue LED indicators will be flashing and the steady LED lights will increase in number corresponding to charge time and power level. (iii) When the LED of your required voltage is lit, release the button and wait for 5 seconds, the flashing LED will stop there, and the voltage of the Output I socket has now been set at your desired voltage and the Power Bank is now ready to supply power at your selected voltage. If you want to change to other voltage setting, you should now press the “ Check / Voltage Selection Button ” again to switch to the output voltage that you require. (ii) The LED of your last voltage setting will start flashing. (i) Press and hold the “ Check / Voltage Selection Button ” for 3 seconds. Follow the steps below to select the desired voltage: There are 3 different outputs of the Output III, i.e., 16V, 19V and 24V. Therefore, whenever you want to fast charge the Power Bank, simply unplug the power cable Z11 from Output Socket I, the AC adaptor will automatically convert to fast charging mode to charge the Power Bank. When the power level of the Power Bank is too low, the Output Socket I will stop charging your device and at the same time the AC adaptor will automatically convert to fast charging the Power Bank. When the Power Bank is being charged by the AC adaptor and simultaneously providing power to your device through its Output Socket I, the AC adaptor will charge the Power Bank at slow charging mode. If you want to select voltage again, you should unplug the power cable Z11 from Output I socket and repeat the “Voltage Selection” of Output I Socket procedures again (see point 7 below) to re-select your desired voltage.įor use with the sockets Output II & Output III, after connecting the Power Bank to your device, you must press the “ Check / Voltage Selection Button ” once to start charging. (ii) When the Output I is NOT loaded, the LED of the last selected voltage will flash for 12 seconds, and then stop. (i) When the Output I is loaded, the LED of the selected voltage will lit until the power cable Z11 is unplugged from the Output I socket. Also, there will be the following 2 scenarios: When the power cable Z11 is plugged into Output I socket, the Voltage Selection function will be SUSPENEDED TEMPORARILY. Select the correct output voltage before plugging the cable into the required output socket. With the provided 19V AC adaptor connected for charging the EL1697 Power Bank, it can still be able to power-up 4 devices through its Output I, Output II and Output III ports simultaneously. But the large screen, long battery life, and latest high-power processor make it especially good for presentations.Please read the following instructions carefully for a good understanding of the product and its functions. The variety of features, along with above-average performance and intuitive design, clearly makes the Omnibook a good option for any mobile professional. The Omnibook's Winstone scores might have been better if the hard drive were 5,400 instead of 4,200 rpm. Its Business Winstone 2001 score was above average, and it came in second on i-Bench 3.0, but it came in last on Content Creation Winstone 2002. It yielded 3 hours 26 minutes on our BatteryMark test, making it the second-best in its class-quite impressive considering the 15.1-inch screen. There is also a vertical scrolling button in the center.Īt 6.2 pounds (system weight), the Omnibook is the heaviest of the mainstream notebooks we reviewed. The Omnibook comes with both a touch pad and pointing stick. Another useful feature is the button and blue LED indictor on the front left-hand side of the unit, which let you easily enable or disable 802.11b wireless connectivity- perfect for switching off wireless connections on the road. On the right side of the unit is a feature that should be standard on more notebooks: a separate hardware volume control and audio-off button with a light indicator that provides a quick mute function without making you fumble around with the keyboard or input device. Best Hosted Endpoint Protection and Security SoftwareĪnother good design choice is the module release latch, a slide switch located on the right front edge of the unit, which makes hot-swapping between the floppy disk drive and the DVD-ROM drive a breeze.